Description

PIC12(L)F1612/16(L)F1613 microcontrollers deliver on-chip features that are unique to the design for embedded control of small motors and general purpose applications in 8/14-pin count packages. Features like 10-bit A/D, CCP, 24-bit SMT and Zero-Cross Detection offer an excellent solution to the variety of applications. The product family also has a CRC+ memory scan and Windowed WDT to support safety-critical systems in home appliances, white goods and other end equipment.

Core Features

• C Compiler Optimized RISC Architecture

• Only 49 Instructions

• Operating Speed:

- DC – 32 MHz clock input

- 125 ns minimum instruction cycle

• Interrupt Capability

• 16-Level Deep Hardware Stack

• One 8-Bit Timer

• One 16-bit Timers

• Low Current Power-on Reset (POR)

• Configurable Power-up Timer (PWRT)

• Brown-out Reset (BOR) with Selectable Trip Point

• Windowed Watchdog Timer (WWDT):

- Variable prescaler selection

- Variable window size selection

- All sources configurable in hardware or software

Memory

• 2 KW Flash Program Memory

• 256 Bytes Data SRAM

• Direct, Indirect and Relative Addressing modes

• High-Endurance Flash Data Memory (HEF):

- 128 B of nonvolatile data storage

- 100K erase/write cycles

Operating Characteristics

• Operating Voltage Range:

- 1.8V to 3.6V (PIC12LF1612/16F1613)

- 2.3V to 5.5V (PIC12F1612/16F1613)

• Temperature Range:

- Industrial: -40°C to 85°C

- Extended: -40°C to 125°C

eXtreme Low-Power (XLP) Features

• Sleep mode: 50 nA @ 1.8V, typical

• Watchdog Timer: 500 nA @ 1.8V, typical

• Secondary Oscillator: 500 nA @ 32 kHz

• Operating Current:

- 8 uA @ 32 kHz, 1.8V, typical

- 32 uA/MHz @ 1.8V, typical

• Up to 11 I/O Pins and One Input-only Pin:

- Individually programmable pull-ups

- Slew rate control

- Interrupt-on-change with edge-select

Digital Peripherals

• Complementary Waveform Generator (CWG):

- Rising and falling edge dead-band control

- Full-bridge, half-bridge, 1-channel drive

- Multiple signal sources

• Two Capture/Compare/PWM (CCP) modules

• Two Signal Measurement Timers (SMT):

- 24-bit timer/counter with prescaler

- Multiple gate and clock inputs

• 8-Bit Timers (TMR2+HLT/4/6):

- Up to 3 Timer2/4/6 with Hardware Limit Timer (HLT)

- Monitors Fault Conditions: Stall, Stop, etc.

- Multiple modes - 8-bit timer/counter with prescaler

- 8-bit period register and postscaler

- Asynchronous H/W Reset sources

• Cyclic Redundancy Check with Memory Scan (CRC/SCAN):

- Software configurable

Intelligent Analog Peripherals

• 10-Bit Analog-to-Digital Converter (ADC):

- Up to 8 external channels

- Conversion available during Sleep

• Up to Two Comparators (COMP):

- Low-Power/High-Speed mode

- Up to three external inverting inputs

- Fixed Voltage Reference at non-inverting input(s)

- Comparator outputs externally accessible

• 8-Bit Digital-to-Analog Converter (DAC):

- 8-bit resolution, rail-to-rail

- Positive Reference Selection

• Voltage Reference:

- Fixed Voltage Reference (FVR): 1.024V, 2.048V and 4.096V output levels

• Zero-Cross Detect (ZCD):

- Detect when AC signal on pin crosses ground

• Two High-Current Drive Pins: - 100mA @ 5V

Clocking Structure

• 16 MHz Internal Oscillator:

- ±1% at calibration

- Selectable frequency range from 32 MHz to 31 kHz

• 31 kHz Low-Power Internal Oscillator

• 4x Phase-Locked Loop (PLL):

- For up to 32 MHz internal operation

• External Oscillator Block with:

- Three external clock modes up to 32 MHz

PIC16F1613-I/ST New and Original in the stock, welcome to send the request to us!